Internal DNS BIND Server Built!

I started this blog on May 8, 2013 with the hopes of sharing some of my I.S. “tinkering”. I’m fully intent on keeping my I.T. skills sharp so I can continue to be relevant in the classroom for Information Systems majors. One of the items on my list was to build an internal DNS server. If there’s anything that is slightly frustrating about a home network, it’s that you usually have to reference your internal devices with their IP Address (192.168.x.x usually). DNS works great for us on the Internet and is a whole lot easier than remembering IP Addresses. However, if your home network expands beyond a router and you have a file server, networked printer, etc., having DNS available to you on your home network can be rather convenient.

To Start

I started by taking an older HP nc6400 laptop with 1.5gb of RAM and installed openSUSE 11.4. 11.4 is an older Linux release, but it was the media I had on hand and Comcast was not being gracious to my download speeds the other night. I went through a typical install. In order to save on memory consumption, I ¬†did a minimal server (text only) install and made sure to set the RunLevel to 3. For running network services like this, there is no reason to have a GUI. Besides, command line is all you really need to survive ūüôā

After the install, I loaded up Yast2, configured the network interfaces and then ran all the software updates that were available. I also needed to get some basic tools that don’t install by default with the operating system like vim.

yast2 -i findutils readline libgcc glibc-devel findutils-locate gcc flex lynx compat-readline4 db-devel wget gcc-c++ make vim telnet cron iptables iputils man man-pages sudo

Then, it was time to install BIND so I could get DNS up and running:

yast2 -i bind bind-chrootenv bind-devel bind-utils

Added to system startup so I didn’t have to start the service when the server rebooted.

chkconfig –add named
/etc/init.d/named start

I have to credit the following site for getting me started.

Configuring BIND

I had co-administered nameservers in my previous role, but I never had to get one going from scratch. This, naturally, didn’t come without a few hiccups. There are several resources online that can help you get this going. After you have BIND installed via the previous steps, you need to configure your /etc/named.conf file. Here are the spots I changed/tweaked from the default.

I set the forwarding DNS servers to the public Google DNS servers. I have much more faith in their 
ability to resolve addresses as opposed to Comcast. Plus, Google has a shorter cache timeout, which means that if an address changes on the web, it will get picked up quicker by Google than Comcast.

forwarders {;; };

Next, I need to setup zone files for both internal DNS lookups and reverse DNS lookups. For example, I want to resolve to and for the reverse, I want to resolve to

zone “” IN {
                allow-transfer { any; };
                allow-query {; };
                type master;
¬† ¬† ¬† ¬† ¬† ¬† ¬† ¬† file “master/”;

zone “” IN {
                allow-transfer { any; };
                allow-query {; };
                type master;
¬† ¬† ¬† ¬† ¬† ¬† ¬† ¬† file “master/”;


Then, it was time to configure the zone files as mentioned in named.conf. In openSUSE, the zone files are stored in /var/lib/named. I first created my file in /var/lib/named/master:
$TTL 7200
@ IN SOA        root.localhost. (
                2013052702      ; serial
                28800           ; refresh, seconds
                7200            ; retry, seconds
                604800          ; expiry, seconds
                86400 )         ; minimum, seconds IN NS 

localhost       IN A  
router          IN A  
gateway         IN CNAME        router
To start with, I wanted to be able to resolve the router IP address and create an alias. The A record establishes the forward DNS lookup and the CNAME is an alias referencing router.

Then, I created my reverse lookup file in /var/lib/named/master:

$TTL 86400
@ IN SOA (
                2013052901      ; serial
                28800           ; refresh, seconds
                7200            ; retry, seconds
                604800          ; expiry, seconds
                86400 )         ; minumum, seconds
                IN NS
1               IN PTR
The 1 in the last line references the last octet of the IP address for the reverse lookup. So, resolves to


When finished, I restarted the BIND service from the command prompt:
# service named restart
To do some testing to make sure things worked, I used the dig and host commands to check my work.
# dig
# host
# dig
These commands should spit back results that indicate that your DNS entries correspond with the right domain and vice-versa.

The last step was to change the configuration on my router to reference the new internal DNS server so all devices on my home network could utilize the new DNS service. Ideally, you should have 2 internal DNS servers in case one fails. Down the road, I may bring up BIND on a separate box for fault tolerance. In the meantime, I made my internal DNS server the primary DNS and Google’s the secondary.¬†

After rebooting the router, I opened up a command window on one of my windows clients and issued the flushdns command. This cleared the local DNS cache so all new addresses would be pulled from the server.
ipconfig /flushdns
I then tried a few simple ping and nslookup commands to make sure things were working locally:

In Closing

All is working and now I can go back and edit my host files to include other static IP addresses I want internal DNS addresses for like printers, file servers, Nintendo WII, etc. At the end of the day, it was a fun tinker. That’s what I was looking for in the end. I’m curious now to see how feasible this is to deploy to students in a lab format so they can tinker as well. From my perspective, it teaches fundamentals on how to install and configure a server in addition to picking up network fundamentals at the same time. We’ll see if this one has viability down the road.¬†

Thanks to the following resources:

I used the following to assist me with configuring my BIND server.